Seadog Heavy Duty Nylon Cleats

Heavy duty black nylon tie-down cleats. They are resistant to salt and sun, and will outlast your boat. Available in 4.5, & 6.25" sizes

42 Piece Stainless Flat Head Tapping Screw Kit

Grab some of these kits for your shop or your boat - or both. You never know when you will need an odd screw, nut or pin.

SeaLect Stainless Pop-Rivet Mount Pad Eye

The fastener pads are flat topped to accept 3/16" pop rivets or pan head screws.316 Stainless Steel K081850A11/32 in.B11/32 in.C1-1/16 in.Fastener3/16" Pop RivetWeight.02 lb.

Buck Algonquin Angle Mount Oarlock Sockets

These are genuine bronze oarlock sockets. They are sand cast by Buck Algonquin. They should be used with Bronze oarlocks. Specifications Material Bronze Overall Width 4 in. Overall Height 1-1/4 in. Hole ID 1/2 in. C. S. Screw...

Racelite Boom Crutch Holder

For fastening to aft cockpit bulkhead. Opening 2-3/4" x 3/4". Takes # 8RH screws.

Plastic Parrel Beads

6 Colors - 6 Shapes - Many Uses Cylinder - This is a good shape for a parrel, not traditional, but I can't see why it would not work just fine. Cube - Obviously this bead will NOT work! But it may have other uses. Let me know...

Seadog Stainless Swivel Eye Boat Snap

Investment Cast 316 Stainless Steel. Part Number A B C SD-146131 3-5/16" 7/16" 3/4"

Sea-Lect Screw Out Deck Plates with Internal Collar

These SEA-LECT Designs Deck Plates are molded with a collar on the bottom to hold deck plate bags or other round containers. Use silicone sealant on hull or deck surface when installing the deck plate. Lubricate with Teflon grease or Vaseline...

SeaLect Kayak Rudder Cable Tubing

Black Nylon rudder cable tubing. 3/16" OD. This is the same material used in the SeaLect Rigging Kit - which has 2 - 15 foot pieces. If you need more than that you can order it by the foot. Typically used with 1/16" Stainless cable.  

Pintle & Gudgeon Fastener Kits

Stainless Steel Pintles and Gudgeons should always be bolted on. Period. We resisted trying to make kits for all the different pintle and gudgeon sets we sell because there are so many different lengths of bolts needed. Finally we figured out that we...

Seadog Stainless Steel Rings

Various sizes, Formed 304 Stainless Steel Part...

Ronstan Urethane Universal Tiller Extension Joint

Smooth, uniform rotation in all directions and a quick, firm reponse to steering movements. The RF3133 universal joint with snap-on cover is designed to allow quick fitting and removal of the tiller extension from the fixed base. A curved surface...

Ronstan Narrow Saddle

316 Stainless ReferenceImperialMetricA15/32 in.12 mmB1/4 in.7 mmC1-3/4 in.44 mmD5/16 in.5.0 mmWeight0.9 oz.25 g

Flathead Silicon Bronze Wood Screws

Silicon Bronze is a fantastic material for boat fasteners. It will outlast even stainless steel in many conditions. Why do we offer Frearson head screws rather than square-drive (Robertson), slotted or Phillips? Well we think they're the best, the point...

Heavy Duty Stainless Swivel Hasp

A high quality, heavy duty stamped 304 Stainless Steel swivel hasp. Takes #8 flat head fasteners.

Navilight Tricolor 2NM - magnetic base

The Navilight Tricolor 2NM - US Coast Guard approved for 2 nautical miles includes a green light to be shown at the starboard side and a red light to be shown at the port side. In addition, it includes the white Sternlight, to be used at the stern. It is...

Windknife Aluminum Extrusions

110.5 cm lengths (43.5 inches) Windknife offers the D.I.Y builder a simple, inexpensive and fast way to create accurate and durable aluminium foils of varying sizes without the need for expensive tooling.We now offer : The "Full Foil 13". click to...

SeaLect Stainless Hammock Hooks

These stainless hooks are attached to a deck to retain a piece of shock cord used to hold down various loose pieces of gear. The picture below shows an example. Part A B C D E SD-671460 15/16" 3/4" 1/2" 1-1/4" 1/2"

Concave Rail Mount Deck Hinges

This hinge is used to mount a bimini to a standard 7/8" rail. It connects to any of our end caps or inserts.

SeaLect Kayak Foot Braces

These are absolutely the best kayak footbraces we have ever seen. They are resistant to any of the things you might run into including water, sand, fish scales, sunlight - nothing will stop these footbraces from working properly. The pedal is molded...

Seadog 4" Open Base Die Cast Cleat

These die cast chrome plated cleats are interchangeable with Perko® style 1210 cleats. Complete w/ galvanized studs, washers and nuts threaded into each leg of the cleat. This eliminates the need for fasteners and provides a clean looking installation...

Seadog Stern Eyes

Sea-Dog® Stern Eyes come with adjustable finish nuts as compared to the crimped ring used on most other Stern Eyes. All parts are 304 stainless steel. Plate sizes: 2-1/4" x 3/4" (plate 1) 3-1/2" x 1-1/2" (plate 2) Part...

Seadog LED Port and Starboard Navigation Lights

Stainless Steel (above)or Black (right) finish - 12 Volt DC. Now you don't have to worry about converting standard nav lights to LED. The LED's actually emit red or green light. This makes them much more effecient than putting white lights behind...

Large Side Mount Bimini Deck Hinges

These are the bottom hinges that screw directly into a coaming or deck to mount a bimini. The photo above shows the difference between top mount and side mount and how the end caps or inserts mount on the hinges.

Racelite RL-261 Camcleat

Similar to the RL-260 camcleat but with a glass-filled flange base for surface mounting. Use four countersunk #8 wood or machine screws. Available with or without stainless steel fairlead/strap. Bolts are on 1-1/2" centers - works best with 7/16" line or...

Racelite Heavy Duty Pintles

3/8" pins - 1" - 1-3/8" rudders These pintles come in two widths and with either short pin or long pin. There is no gudgeon included. All parts are stainless steel - Fits 1" or 1-3/8" thick rudder. (note: pintle tangs can be easily adjusted for rudders...

Ronstan Stainless Steel Gudgeons

These gudgeons are used together or with pintles having 1/4" pins. You can use a pin in each set, as in the illustration or a single pin going through all four gudgeons.Parts sold individually or as complete set. Pins not included. You may want a 1/4" SS...

Omer 18 Gauge Pneumatic Brad-Nailer

Recommended Tool for Raptor 18 Gauge Composite Brads The Omer 12P.25 Brad Nailer drives the full range of Raptor® B/18 18 gauge plastic brad nails from 7/16" (11mm) through 1" (25mm) lengths. The narrow nose allows for superior nail placement in hard...

Seadog Removable LED All Around Light

Injection Molded Nylon/Chrome Plated Zinc. LED Removable All Around Lights are approved for USCG 2NM (Colreg 2 mile). 12 Volt DC. Note: drawing is not proportional   Part # A B C D Fastener SD-400015 24-5/8" 18-1/2" 5/8" 2-7/8" #8FH

Navimount Horizontal Base

The Navimount Horizontal is designed to attach the Navimount Pole or the Navilights with Navimount base (model 040, 340) to horizontal surfaces - e.g. the boat deck or cabin roof. Includes- two self tapping stainless steel screws Technical Specs Size: H...

Loop Clamcleats

A nylon cleat with a tooth design that offers a quick, positive lock that is easy to release. Works with line sizes 1/8" to 1/4" (3-6mm). The side entry fairlead allows the cleat to be hooked onto the line, without threading the rope through an eye,...

Medium Nylon Sheaves

Injection molded nylon If you have read some of the articles in Duckworks about making your own Blocks (see links below), and want to try it, but are uncertain about making the sheaves, this may be what you need. These durable Nylon pulleys are also...

Stainless Steel Washers

#10 through 3/4"

Teak Handrails

We brought these solid teak handrails in to service West Wight Potter owners, as the small one-loop rail is OEM for the Potter 15 and the larger 3-loop is OEM for the Potter 19, but these beautiful, smooth-finished teak handrails would work on any small...

Racelite Moveable Goosenecks for Bolt Rope Slot

RL-252-A - goes in 1/2" boltrope grove in mast and screws to standard boomShown with tangs

Snap On/Off Bimini Side Mount

Injection Molded Nylon If you want a bimini that will easily snap out to be completely removed, and is side mounted, you may want to consider this pair. We only have them for 3/4" tubing (also fits 1/2" electrical conduit). The bracket is screwed or...

SeaLect Kayak Recreational Foot Braces

SEA-LECT Designs Kayak Recreational Footbraces are designed to be maintenance free with tremendous strength - at a price that's attractive to everyone! With three attachment options and low profile pedal that mounts easily in most boats, this footbrace...

Bimini Top Caps

Used on the ends of bimini tubing sections These are used at the ends of the metal hoops which hold up the fabric on a bimini. We have inserts and caps for both 3/4" and 7/8" tubing. Usually Aluminum is used, but we have found that the inserts for 3/4"...

Ronstan 1/4" Tang

6.4mm (1/4") dia. clevis pin, 51mm (2") long, 1 x 6.4mm (1/4") fixing holeUsed for terminating wire riggingGrade 316 stainless steel0.7 oz. - 20 g

Racelite Stainless Exit Plates

Stamped stainless steel For use where a line or wire has to pass through a deck or spar Both plates are 1-1/4" x 2" x 1/16" thick. There are four holes for #8 fasteners and they will pass up to a 3/8" line, wire or rod. The RL-255C is curved to mount on...

Sealect Performance Kayak Hatches

For replacements or new boat constructionNot sure which hatch fits your production boat? Click here for a partial list of manufacturers and hatch part numbers. Part# Outside edge of raised mounting ring Max Size * Minimum...

Cast Brass Heavy Duty Lift Handles

Once in a while you get something in the mail that is actually more robust than you had hoped rather than the other way around. That is the case with these handles. They weigh almost half a pound apiece. Solid cast brass, the SD-222356 has a polished...

Nylon Lateral Clamcleats

Injection molded Nylon Sea-Dog Nylon lateral clamcleats - mount on either side of a centerboard case, on gunwales, coaming, or other vertical surface.

Seadog Stainless Bow Chocks, pair

Keep anchor or dock lines from chafing gunwale or other parts of your boat. Investment Cast 316 Stainless - these are hefty, high quality parts. They will look good on any boat.Part#ABCDFastenerSD-0600404-3/4"13/16"1/2"3-5/16"#10FH

Navisafe Skiff & Dinghy Complete Kit

The Navisafe Complete Dinghy Kit is probably the most flexible and easy to mount pack of all lights and mountings needed to equip most dinghys and small sailboats up to 12m with Navigation lights in compliance with COLREG 72.Comfortable storage in...

Side Mount Bimini Slide Hinges

Injection Molded Nylon

Viadana 1/4" Fairlead with SS Liner

Racelite Shroud Adjuster

This is the RL 349 adjuster for shrouds.

Buck Algonquin Bronze Bow Eye

Sand cast bronze only for the saltiest of boats. Specifications FINISH Cast Finish MATERIAL Plain Bronze SHANK LENGTH 6 in SHANK DIAMETER 3/8 in EYE DIAMETER 1 in WEIGHT 0.45 lb NOTE The bronze bow eyes come with a shouldered stem.

Racelite 1/2" Heavy Duty Gudgeons

Takes 1/2" pintles There are two different gudgeons in this style - one two hole and one four hole - both take 1/2" pintles. Each gudgeon is actually composed of two parts as shown below. All parts are stainless steel.Typically the four hole gudgeon is...