null

Motor Boats to 16'

  • Power 14 Plans

    Power 14 Plans

    The hull for this launch was originally based on our Power 16 model but instead of going for a simple flat bottom panel, we have used a 'V' bottom shape. Whilst this makes construction time a little longer it gives a slightly better ride in choppy...
    $122.00
    Choose Options
  • 12' Sand Martin Simple Runabout Plans

    12' Sand Martin Simple Runabout Plans

    Using between 5 and 6 sheets of 6mm ply the Sand Martin uses simple stitch and tape technology in her construction. She can be fitted out in a number of different ways but the standard arrangement shows two thwarts with side benches aft and a foredeck...
    $88.00
    Choose Options
  • 15' Lobster Boat Plans

    15' Lobster Boat Plans

    This motorboat is based on a typical Maine Lobster boat and has been designed for strip plank construction (although she could be built using clinker/ply techniques using the same moulds). The hull has a high freeboard with flat planing sections aft and...
    $27.00 - $135.00
    Choose Options
  • Power 1 Plans

    Power 1 Plans

    16'x5'6" ply motor launch of ultra simple construction using pre-shaped ply hull panels, frames and transom. The chine joints are completed with epoxy resin fillets and tape making construction quick. A weekend's work will see the hull panels marked out,...
    $108.00
    Choose Options
  • 8' Skiffle Junior Motor Boat Plans

    8' Skiffle Junior Motor Boat Plans

    The 8' Skiffle is a simple motor boat designed for children to use although she can accommodate a small adult. The hull uses a flat bottom panel with single bilge and side panels and uses simple stitch & tape methods in her construction. She can take...
    $74.00
    Choose Options
  • 16' Whooping Swan Plans

    16' Whooping Swan Plans

    The Whooping Swan is a development of the 16' Grey Swan pocket cruiser - a client asked me to alter the hull so that it would take an outboard with a wheelhouse - in doing this we have added buoyancy to the aft end and made the transom more vertical to...
    $27.00 - $169.00
    Choose Options
  • 15' Rascal Motor Dory/Skiff Plans

    15' Rascal Motor Dory/Skiff Plans

    This is a simple and very easily built motor dory for use with outboards up to around 50 hp in size. She can either be made by wrapping the pre-shaped sides around the frames, fastening on an external chine stringer and then putting the bottom ply on...
    $68.00
    Choose Options
  • 15'4" Fly Fishing  Coble Plans

    15'4" Fly Fishing Coble Plans

    This design has been based upon our Northumbrian Coble designs - the client wanted a very stable seaworthy design mainly for outboard power but which could also be rowed and take a sail plan. Basic construction is for stitch and tape but the moulds/jig...
    $135.00
    Choose Options
  • 12' Taw Plans

    12' Taw Plans

    The 12'Taw is a simple 'V' bottomed plywood runabout for two people. Construction starts with the plywood frames/bulkheads being slotted onto a plywood central girder and the transom fitted. Bottom stringers are added to stiffen the bottom area...
    $27.00 - $135.00
    Choose Options
  • Harrier 13' Motor Dory Plans

    Harrier 13' Motor Dory Plans

    The Harrier is a simple single chined 'V' bottomed stitch and tape ply dory for outboard power. She has been designed to give as much carrying capacity as possible in a 13' car-toppable boat making her suitable for fishing and picnicking as well as for...
    $88.00
    Choose Options
  • 9'6" Little Harrier Motor Dory Plans

    9'6" Little Harrier Motor Dory Plans

    This is a smaller sister to the 13’ Harrier—she has the same simple ‘V’ bottomed hull shape which has plenty of stability and room in such a short length for fishing and pic-nicking. Under the seats can be used for flotation and/or stowage and...
    $74.00
    Choose Options
  • 16' Cape Cod Semi Dory Plans

    16' Cape Cod Semi Dory Plans

    The Cape Cod is a motor dory based upon the Swampscott model with it's flat but rockered bottom panel and 4 planks per side. Unlike the sailing Swampscott, the bottom is kept fairly wide aft so that she can take a reasonable size of outboard (up to 35...
    $101.00
    Choose Options
  • 15' Electric Skiff Plans

    15' Electric Skiff Plans

    A lovely little skiff made from four sheets of 1/4’’ plywood using simple stitch and tape techniques. She has a fine entry for moving quickly and easily under electric outboard power (a conventional petrol outboard may also be used) with a stern wide...
    $74.00
    Choose Options
  • Shetland 14 Workboat Plans

    Shetland 14 Workboat Plans

    This sturdy craft has been designed for a client in Scotland who wanted a rugged general purpose boat for fishing and diving in rough water. She may only be 14’ long, but she is for all that, a large boat and she incorporates both integral buoyancy...
    $101.00
    Choose Options
  • 15'1" Port Pegasus Plans

    15'1" Port Pegasus Plans

    The Port Pegasus is a clinker boat which may be used as a pure rowing boat or fitted with a small diesel (ie Farymann 7.5) as a small motor launch with classic appearance.   As a general purpose launch, she could be fitted out in a variety of...
    $27.00 - $162.00
    Choose Options
  • Power 1.2 Plans

    Power 1.2 Plans

    The Power 1.2 is a development of our Power 1 design. She has increased beam and the chine has been lowered to give a more stable shape so that her side decks can be used comfortably. The drawings give details for a cabin arrangement with 2 full length...
    $135.00
    Choose Options
  • 16' Curlew Motor Punt Plans

    16' Curlew Motor Punt Plans

    This is a very simple stitch and tape design using 5 sheets of 9mm (3/8") ply with pre-shaped hull panels and transoms. With a beam of 4'6" and a mid depth of 16" she has plenty of room for fishing, camping or for family pic-nics.She may be rowed but is...
    $81.00
    Choose Options