Rudder & Tiller

Weekender Vertical Gudgeon

These gudgeons were developed for the Weekender Set, but will work with many of our 3/8" pintles. (see chart to figure out which will work) They are designed to be mounted vertically in cases where the boat is a double-ender or where a...

Rudder Hardware for Scamp

This set is recommended by John Welsford for Scamp. The tangs are 2-1/8 inches wide and the pintles have a sturdy 3/8" pin.This set consists of two gudgeons and two pintles. There is no hold down included. All parts are stainless steel. (note: pintle...

Tiller Lock Kit

This Tiller Lock Kit is a patent pending rudder locking device with unlimited variability designed for all tiller controlled boats. The locking of the tiller is effected by a short pull upward which causes the control line to be firmly locked around the...

Racelite 1/2" Pin Heavy Duty Pintles

1/2" pins - 1" & 2" rudders These pintles come in two widths and with either short pin or long pin. There is no gudgeon included. All parts are stainless steel - Fits 1" or 2" thick rudder. (note: pintle tangs can be easily adjusted for rudders as...

Racelite Heavy Duty Rudder Gudgeons

See our pintle & gudgeon compatibility chart Our RL-690 rudder gudgeons are similar to our RL-490 pintles but with no pin. They can be used with the RL-690 transom pintle or with the RL-490 gudgeon if a bolt or rod is run through...

Weekender Rudder Hardware Set (includes pins and rings)

This is a very robust set of stainless steel rudder hardware. The vertical gudgeon that bolts against the transom is a full 1/8th (0.125) of an inch thick and 1.25" wide. The rudder gudgeons are made from 1" wide strap and are 3/32 (0.090)" thick. The...

Weekender Rudder Gudgeon

These gudgeons were developed for the Weekender Set, but will work with many of our 3/8" pintles. (see chart to figure out which will work) They can also be used on a skeg where a regular gudgeon is used as the upper pivot point. Weekender Rudder...

Canoe/Kayak Rudder Gudgeons

For sharply pointed sterns After a lot of consulting with the folks at Race-Lite and with substantial help from Matt at JEM watercraft, we have finally come up with a good solution to the problem of attaching rudders to canoes and kayaks. Use two of...

Racelite Heavy Duty Transom Pintles

Our RL-690 transom pintles are the same as used on most Lightning class sailboats. They are typically mounted on a flat transom and paired with a rudder gudgeon. More details under "Particulars" tab. To find out which gudgeons work with these pintles,...

Racelite Light Duty Gudgeons

See our pintle & gudgeon compatibility chart Light duty stainless transom mount gudgeon from Racelite. See Particulars for dimensions. RL-358Light duty stainless steel gudgeon 5/8" x 4" x 1/16"pin - 5/16"takes #10 fastener  

Rudder Hold-downs

RL-336 - Spring TypeStainless Steel spring rudder hold-down - 4" long x 3/4" wide - may be used with any of our pintles and gudgeons. RL-337 - Swivel TypeStainless Steel swivel hold-down - 1" long x 5/8" wide - may be used with any of our pintles and...

Set of Light Duty Pintles and Gudgeons

See our pintle & gudgeon compatibility chart This set consists of two gudgeons, one short pin pintle, and one long pin pintle. There is no hold down included. All parts are stainless steel - Fits 3/4" or 1-3/16" thick rudder. (note: pintle tangs can...

Set of Medium Duty Pintles and Gudgeons

This set consists of two gudgeons, one short pin pintle, and one long pin pintle. There is no hold down included. All parts are stainless steel - Fits 3/4" or 1-3/8" thick rudder. (note: pintle tangs can be easily adjusted for rudders as much as 1/4"...

Racelite One Piece Gudgeons

A one piece gudgeon ideal for small boats such as PDRacers. Pintle holes are 5/16" but could be drilled to 3/8".Feedback:I recently installed a Racelite 358BR gudgeon as a retrofit on my son's PDRacer (Hull #491). The original rudder hardware consisted...

Racelite Extra Heavy Duty Gudgeons

Extra Heavy duty stainless transom mount gudgeon from Racelite. See Particulars for dimensions. RL-490Extra heavy duty stainless steel gudgeon thickness - .090" plus reinforcing strap3/4" wide x 5-1/4" long x 1" highpin - 3/8"takes...

Racelite Tiller Extension Swivel

Often you want a push-pull tiller extension so that you can steer the boat from up on the rail or even from the bench seat if the boat is particularly beamy. This simple swivel from Race-Lite will fill the bill. Two round head #8 or #10 screws mount it...

Ronstan Urethane Universal Tiller Extension Joint

Smooth, uniform rotation in all directions and a quick, firm reponse to steering movements. The RF3133 universal joint with snap-on cover is designed to allow quick fitting and removal of the tiller extension from the fixed base. A curved surface...

Racelite Heavy Duty Pintles

3/8" pins - 1" - 1-3/8" rudders These pintles come in two widths and with either short pin or long pin. There is no gudgeon included. All parts are stainless steel - Fits 1" or 1-3/8" thick rudder. (note: pintle tangs can be easily adjusted for rudders...

Ronstan Stainless Steel Gudgeons

These gudgeons are used together or with pintles having 1/4" pins. You can use a pin in each set, as in the illustration or a single pin going through all four gudgeons.Parts sold individually or as complete set. Pins not included. You may want a 1/4" SS...

Racelite 1/2" Heavy Duty Gudgeons

Takes 1/2" pintles There are two different gudgeons in this style - one two hole and one four hole - both take 1/2" pintles. Each gudgeon is actually composed of two parts as shown below. All parts are stainless steel.Typically the four hole gudgeon is...

Racelite Light Duty Pintles

5/16" pins - 3/4" - 1-3/16" rudders These pintles come in two widths and with either short pin or long pin. There is no gudgeon included. All parts are stainless steel - Fits 3/4" or 1-3/16" thick rudder. (note: pintle tangs can be easily adjusted for...

Sets of Extra Heavy Duty Transom Pintles and Rudder Gudgeons

See our pintle & gudgeon compatibility chart This set consists of two gudgeons and two pintles. There is no hold down included. All parts are stainless steel - Fits 1-1/2" through 3" thick rudders. (note: pintle tangs cannot be adjusted for rudder...

Racelite Medium Duty Pintles

3/8" pins - 3/4" - 1-1-4" rudders These pintles come in two widths and with either short pin or long pin. There is no gudgeon included. All parts are stainless steel - Fits 3/4" or 1-1/4" thick rudder. (note: pintle tangs can be easily adjusted for...

Racelite Extra Heavy Duty Pintles -

3/8" pins - 3 different options These pintles are somewhat adjustable like the Racelite 300 series pintles but heavier. You would probably want to use the narrow pintles with a metal rudder. These have a single pin length option and nominally fit a 7/16"...

Kayak Rudder Mounting Gudgeons

If you want to install a Sea-Lect TruCourse Rudder on your boat and it does not have a standard mounting gudgeon, you will need the appropriate gudgeon. Study the photos and diagrams below to determine which model you need. Four different...

Racelite Medium Duty Gudgeons

Medium duty stainless transom mount gudgeon from Racelite. See Particulars for dimensions. See our pintle & gudgeon compatibility chart RL-360 gudgeonMedium duty stainless steel gudgeon thickness - 5/64"3/4" x 3-3/4" pin - 3/8"takes #10...

Racelite Extra Heavy Duty Pintles

3/8" pins - 1-1/2" - 3" rudders These pintles come in several widths but only one pin length. There is no gudgeon included. All parts are stainless steel - Fits 1-1/2" through 3" thick rudders. (note: pintle tangs cannot be adjusted for width) For...

Viadana Transom Pintles and Rudder Gudgeons

Rudders from 1/2" to 1-3/8" A set consists of two gudgeons and two pintles. The parts here are sold individually OR in sets. The parts sold individually are represented in the first chart below - you'll need to order two each of the rudder gudgeons and...

Set of Extra Heavy Duty Pintles and Gudgeons

See our pintle & gudgeon compatibility chart This set consists of two gudgeons and two pintles. There is no hold down included. All parts are stainless steel - Fits 1-1/2" through 3" thick rudders. (note: pintle tangs cannot be adjusted for rudder...

Set of Light Duty Pintles and One Piece Gudgeon

Stainless Steel See our pintle & gudgeon compatibility chart This set consists of one gudgeon, one short pin pintle, and one long pin pintle. There is no hold down included. All parts are stainless steel - Fits 3/4" or 1-3/16" thick rudder. (note:...

Set of 1/2" Pin Heavy Duty Pintles and Gudgeons

See our pintle & gudgeon compatibility chart

Racelite Heavy Duty Gudgeons

Heavy duty stainless transom mount gudgeon from Racelite. See Particulars for dimensions. See our pintle & gudgeon compatibility chart RL-390 gudgeonHeavy duty stainless steel gudgeon thickness - 5/64" 3/4" x 3-3/4" pin - 3/8"takes #10...

Factory West Wight Potter 15 and 19 Gudgeon

sold individually - mounting fasteners not included

Set of Heavy Duty Pintles and Gudgeons

Ideal for larger boats See our pintle & gudgeon compatibility chart This set consists of two gudgeons, one short pin pintle, and one long pin pintle. There is no hold down included. All parts are stainless steel - Fits 1" or 1-3/8" thick rudder...

TillerClutch

Conveniently mounted below the tiller - it's out of the way but easy to access. No knobs to turn, no friction to fight, nothing to strip out or snap off. The TillerClutch is made from anodized aluminum and stainless steel. Simple on/off lever is easy to...

Extra Heavy Duty 1/2" Gudgeons

These gudgeons have 1/2" diameter holes for pins. The gudgeons and tangs are formed from 1/8" thick stainless steel and are very robust. We do not have pintles that fit these gudgeons. RL-890 1-1/4" x 1-7/8" x 5-1/4"accepts 1/2" pin mounting holes...