null

Motor Boats

  • Clyde 18 Plans

    Clyde 18 Plans

    The Clyde 18 is a modified Power 1.3 Mk 1 design. The hull shape is a simple deadrise type, single chine 'V' bottomed. The hull is parallel sectioned aft of the wheelhouse which means that she can be easily lengthened or shortened. Construction is for...

    $27.00 - $230.00
    Choose Options
  • Jarvis 21 Plans

    Jarvis 21 Plans

    Below are photos of Tim Thedon's Jarvis 21 under construction.               21' Jarvis Particulars LOA 21'4" 6.52m Beam (excl. gunwale rubbers) 7'9"" 2.35m Hull Mid Depth 3'4" 1...

    $34.00 - $311.00
    Choose Options
  • 55' Trinity Cove Motor Yacht Plans

    55' Trinity Cove Motor Yacht Plans

    This new design was originally drawn up for Cedar Strip construction but drawings were added later for single skin GRP construction too with the plug based on the original strip planked hull. The hull uses the classic easily driven shape of our...

    $68.00 - $810.00
    Choose Options
  • Power 14 Plans

    Power 14 Plans

    The hull for this launch was originally based on our Power 16 model but instead of going for a simple flat bottom panel, we have used a 'V' bottom shape. Whilst this makes construction time a little longer it gives a slightly better ride in choppy...

    $122.00
    Choose Options
  • 26' Saltee Island Plans

    26' Saltee Island Plans

    This is a rugged steel workboat/fishing boat for coastal and offshore use. She has a large cockpit and enclosed wheelhouse with space below for a simple wc and/or galley. The steel hull panel shapes are given so that the hull can be...

    $34.00 - $385.00
    Choose Options
  • 12' Sand Martin Simple Runabout Plans

    12' Sand Martin Simple Runabout Plans

    Using between 5 and 6 sheets of 6mm ply the Sand Martin uses simple stitch and tape technology in her construction. She can be fitted out in a number of different ways but the standard arrangement shows two thwarts with side benches aft and a foredeck...

    $88.00
    Choose Options
  • 16' Egret Runabout Plans

    16' Egret Runabout Plans

    The Egret is a slightly simplified form of the Classic runabout - she has a plywood hull which can be overlaid with Mahogany veneer and teak decking to give a classic look. She has tumblehome aft and a 'V' bottomed hull with a single chine built over a...

    $27.00 - $169.00
    Choose Options
  • 15' Lobster Boat Plans

    15' Lobster Boat Plans

    This motorboat is based on a typical Maine Lobster boat and has been designed for strip plank construction (although she could be built using clinker/ply techniques using the same moulds). The hull has a high freeboard with flat planing sections aft and...

    $27.00 - $135.00
    Choose Options
  • 24' Orwell Commuter Launch Plans

    24' Orwell Commuter Launch Plans

    A slightly modern 'take' on a classic type of launch - many built in the mid 20th Century were much larger so this is a mini version. Half the launch is outside seating in an open cockpit and half is simple accommodation in the form of a couple of...

    $34.00 - $340.00
    Choose Options
  • Power 4 Plans

    Power 4 Plans

    After many requests, we have extended the simple concept of the Power 1 and 2 motor launches to a length of 32' with a beam of 10'9". At the moment, the drawings for the hull and deck construction are available allowing the client to choose or design...

    $540.00
    Choose Options
  • 57' Avoncliff Wide Beam Barge Plans

    57' Avoncliff Wide Beam Barge Plans

    These plans are for the steelwork only of a 17.45m (57') wide beam barge. The plan set consists of 6 drawings covering Hull Construction, Hull Construction Details, Deck/cabin Construction, Deck/cabin construction details, Hull panel shapes and Rudder...

    $47.00 - $405.00
    Choose Options
  • 45' Teign Motor Barge Plans

    45' Teign Motor Barge Plans

    One of our clients wanted to match the advantages of strip planking with an easily built but attractive motor barge hull. In stead of using a slab sided hull seen on so many modern steel barges, we have been able to use the ability of strip planking to...

    $47.00 - $608.00
    Choose Options
  • Power 1 Plans

    Power 1 Plans

    16'x5'6" ply motor launch of ultra simple construction using pre-shaped ply hull panels, frames and transom. The chine joints are completed with epoxy resin fillets and tape making construction quick. A weekend's work will see the hull panels marked out,...

    $108.00
    Choose Options
  • 8' Skiffle Junior Motor Boat Plans

    8' Skiffle Junior Motor Boat Plans

    The 8' Skiffle is a simple motor boat designed for children to use although she can accommodate a small adult. The hull uses a flat bottom panel with single bilge and side panels and uses simple stitch & tape methods in her construction. She can take...

    $74.00
    Choose Options
  • Power 225 Motor Cruiser Plans

    Power 225 Motor Cruiser Plans

    The Power 225 is based upon the "U" shaped hull section of our Power series of motor boats. At present we have the hull panel, frame shapes and construction details for an aluminium version of this boat - accommodation and fit-out details are not...

    $338.00
    Choose Options
  • 26' Ijssel Launch Plans

    26' Ijssel Launch Plans

    It had to happen of course - having designed 21' and 30' Ijssel launches, someone would want something in between and here it is. The hull is very much of the Ijssel high volume stable model with plenty of space for whatever internal arrangement you need...

    $34.00 - $385.00
    Choose Options
  • Mylor 27' Strip Planked Fishing Boat Plans

    Mylor 27' Strip Planked Fishing Boat Plans

    A 27' Fishing Boat for Mr. J. Clarke - this is a high volume strip planked fishing boat of modern proportions - the drawings are for the hull construction only - the mould shapes are computer faired and her tough hull uses 2 layers of strip plank which...

    $270.00
    Choose Options
  • 55' Plywood Motor Yacht Plans

    55' Plywood Motor Yacht Plans

    These drawings show the construction details for the plywood hull only of a 55' x 15' (16.78m x 4.58m) single chine (with spray rail) 'V' bottomed motor yacht capable of speeds up to 25 or more knots. Full details including computer generated and...

    $371.00
    Choose Options
  • 35' Steel Motor Yacht Plans

    35' Steel Motor Yacht Plans

    Similar to the 55 footer below, we have details for the construction of a 35' steel motor yacht hull. The plans include the steel work drawings for the hull and engine beads and the computer generated hull panel shapes. She has a beam of 11'6" (3.5m)...

    $4.10 - $270.00
    Choose Options
  • 32' X 10' Motor Barge Plans

    32' X 10' Motor Barge Plans

    This is a shortened version of the 45' Teign Motor Barge and has the same flat bottom panel for maximum capacity and ease of construction. We have the plans for the hull construction in, strip plank, plywood and steel. Also note that we have now added...

    $47.00 - $473.00
    Choose Options
  • 32' x 6' 9" Steel Canal Tug Plans

    32' x 6' 9" Steel Canal Tug Plans

    We have drawn up the steel construction details (hull, deck, sterngear and rudder details only) for this 32' canal boat based on a tug design with a fantail aft end and narrow boat lines amidships running into a tug type bow. She may be fitted out in a...

    $34.00 - $223.00
    Choose Options
  • 20'/22' Kennet Slipper Launch Plans

    20'/22' Kennet Slipper Launch Plans

    The Kennet can be built either as a 20' or a 22' slipper launch details and panel shapes are given on the plans for both versions. She has a "V" bottom forward which flattens out as it runs aft giving an easily driven hull shape which has plenty of grip...

    $34.00 - $236.00
    Choose Options
  • Rufus 17 Plans

    Rufus 17 Plans

    The RUFUS 17' motor boat is a simple rugged craft with jaunty good looks. She has 3 chines per side and plenty of freeboard and beam, giving her an excellent carrying capacity and very good stability. She can be made as a simple open launch, in which...

    $27.00 - $203.00
    Choose Options
  • 30' Ijssel Launch Plans

    30' Ijssel Launch Plans

    An American client wanted to produce a replica of the African Queen and saw our Ijssel launch as offering a craft of similar style - so we increased her length to 30' and beam to 8' (later we were asked to increase the beam still further to 10' and this...

    $41.00 - $405.00
    Choose Options
  • 26' Skellig Wood Fishing/Workboat Plans

    26' Skellig Wood Fishing/Workboat Plans

    The Skellig 26 is a wood version of the Saltee Island. She has the same rugged hull design for use as a workboat/fishing boat for coastal and offshore use. She has a large cockpit and enclosed wheelhouse with space below for a simple wc and/or galley...

    $34.00 - $385.00
    Choose Options
  • Skellig 19 Plans

    Skellig 19 Plans

    The Skellig 19 is based on our Skellig 18 workboat/fishing boat. In this case the client wanted a slightly bigger boat made of steel to be used as a strong and rugged work/fishing boat in Irish waters. The hull plating is 3mm over 4x75mm frames...

    $27.00 - $236.00
    Choose Options
  • 16' Bourne Runabout Plans

    16' Bourne Runabout Plans

    The 16' Bourne runabout is partly based on the Egret but with a forward raking transom and a fair amount of tumblehome in the aft quarters. She uses the same ply skin over a slotted together ply framework but the tumblehome area is planked using diagonal...

    $27.00 - $169.00
    Choose Options
  • 57' Avoncliff Narrow Boat Plans

    57' Avoncliff Narrow Boat Plans

    These plans are for the steelwork only of a 17.45m (57') narrowboat. The plan set consists of 7 drawings covering Hull Construction, Hull Construction Details, Deck/cabin Construction, Deck/cabin construction details, Hull panel shapes, Rudder and engine...

    $47.00 - $405.00
    Choose Options
  • 25' Windsor Slipper Launch Plans

    25' Windsor Slipper Launch Plans

    For the Windsor slipper launch we have used the ply over frame method of construction using a modern framework of ply bulkheads and frames partly linked by fore and aft ply girders all set up to make sure that the builder starts with an accurate base...

    $34.00 - $270.00
    Choose Options
  • Power 2 Plans

    Power 2 Plans

    A 21' x 7' bigger sister to the Power 1 design using the same easy construction method and having a similar double chine construction with a flat bottom panel simplifying her building and producing an easy planing hull form. The hull, seats and cabin...

    $34.00 - $135.00
    Choose Options
  • 16' Whooping Swan Plans

    16' Whooping Swan Plans

    The Whooping Swan is a development of the 16' Grey Swan pocket cruiser - a client asked me to alter the hull so that it would take an outboard with a wheelhouse - in doing this we have added buoyancy to the aft end and made the transom more vertical to...

    $27.00 - $169.00
    Choose Options
  • Howth Head 22 Plans

    Howth Head 22 Plans

    The Howth Head is a plywood version of the steel Lambay Island design. Like the Lambay, she is a 22' motor boat with a large cockpit area and comfortable accommodation with 2 large berths, w.c. compartment and galley with dining space in the cockpit...

    $34.00 - $304.00
    Choose Options
  • 24'6" Snipe Runabout Plans

    24'6" Snipe Runabout Plans

    This was an interesting way to start a design. The client had a couple of Super Snipe engines kicking about and he wanted to sell them. What better way to do it and to get the greatest return for his money than to package them. The package that we chose...

    $34.00 - $270.00
    Choose Options
  • 15' Rascal Motor Dory/Skiff Plans

    15' Rascal Motor Dory/Skiff Plans

    This is a simple and very easily built motor dory for use with outboards up to around 50 hp in size. She can either be made by wrapping the pre-shaped sides around the frames, fastening on an external chine stringer and then putting the bottom ply on...

    $68.00
    Choose Options
  • Power 2.2 Plans

    Power 2.2 Plans

    This craft is a widened and a more sophisticated version of our Power 2 design. The bottom panel has been slightly veed to give a softer ride and her depth has been increased. This along with her wider beam enables her to be fitted out with a more...

    $27.00 - $169.00
    Choose Options
  • 22' Rufus Motor Cruiser Plans

    22' Rufus Motor Cruiser Plans

    The standard 17' Rufus plans include the frame and panel shapes for both a 20' and a fantailed stern version but we have been getting many requests for a slightly longer version and so we jumped at the chance to draw up a completely new set of plans when...

    $34.00 - $338.00
    Choose Options
  • 36' Bullfinch Narrow Boat Plans

    36' Bullfinch Narrow Boat Plans

    The Bullfinch is a typical standard steel narrow boat with a cruiser stern for home construction. The drawings and details are for the hull, deck and superstructure steel work only. Engine bed and rudder details are also shown. A study plan showing a...

    $34.00 - $236.00
    Choose Options
  • 18' Red Shrike Runabout Plans

    18' Red Shrike Runabout Plans

    Designed along the lines of a traditional 1930's runabout with rounded tumblehome to the topsides at the transom, the drawings detail her for construction using computer generated frames/bulkheads, transom and stem. Ribbands are then slotted into the...

    $34.00 - $270.00
    Choose Options
  • Jarvis 17 Plans

    Jarvis 17 Plans

    The Jarvis 17' motor launch has been drawn up for clinker/ply construction - a building jig is made which consists of chipboard mould shapes mounted on a strongback. Ribbands (stringers) are inserted into the moulds at each lap and these help in...

    $27.00 - $169.00
    Choose Options
  • 15'4" Fly Fishing  Coble Plans

    15'4" Fly Fishing Coble Plans

    This design has been based upon our Northumbrian Coble designs - the client wanted a very stable seaworthy design mainly for outboard power but which could also be rowed and take a sail plan. Basic construction is for stitch and tape but the moulds/jig...

    $135.00
    Choose Options
  • Lambay Island 22 Plans

    Lambay Island 22 Plans

    This is a 22' motor boat with a large cockpit area and comfortable accommodation with 2 large berths, w.c. compartment and galley with dining space. The drawings are originally for steel construction but she could be made out of plywood over a simple...

    $34.00 - $304.00
    Choose Options
  • 41' Humber Steel Motor Barge Plans

    41' Humber Steel Motor Barge Plans

    This is a steel multi-chine motor barge for use in the waters of the UK and Europe, crossing the Channel and exploring the rivers and canals of the European mainland. She has a section of parallel middle-body which means that she can be stretched. She...

    $47.00 - $608.00
    Choose Options
  • 12' Taw Plans

    12' Taw Plans

    The 12'Taw is a simple 'V' bottomed plywood runabout for two people. Construction starts with the plywood frames/bulkheads being slotted onto a plywood central girder and the transom fitted. Bottom stringers are added to stiffen the bottom area...

    $27.00 - $135.00
    Choose Options
  • Ceecan 19 Plans

    Ceecan 19 Plans

    CEECAN is a simple river cruiser for outboard power. Her hull may be stretched or shortened to suit and her superstructure and deck layout changed to you own requirements. The drawings give details for the hull and superstructure construction. She may...

    $27.00 - $135.00
    Choose Options
  • Rathlin 20 Motor Yacht Plans

    Rathlin 20 Motor Yacht Plans

    For Motor Sailer Supplement Click HERE Our Rathlin design is not the type of motor yacht that you would normally see these days as a new ‘‘modern’’ design. Most new craft of the motor type to come off the drawing board now,...

    $27.00 - $338.00
    Choose Options
  • Harrier 13' Motor Dory Plans

    Harrier 13' Motor Dory Plans

    The Harrier is a simple single chined 'V' bottomed stitch and tape ply dory for outboard power. She has been designed to give as much carrying capacity as possible in a 13' car-toppable boat making her suitable for fishing and picnicking as well as for...

    $88.00
    Choose Options
  • 9'6" Little Harrier Motor Dory Plans

    9'6" Little Harrier Motor Dory Plans

    This is a smaller sister to the 13’ Harrier—she has the same simple ‘V’ bottomed hull shape which has plenty of stability and room in such a short length for fishing and pic-nicking. Under the seats can be used for flotation and/or stowage and...

    $74.00
    Choose Options
  • 16' Cape Cod Semi Dory Plans

    16' Cape Cod Semi Dory Plans

    The Cape Cod is a motor dory based upon the Swampscott model with it's flat but rockered bottom panel and 4 planks per side. Unlike the sailing Swampscott, the bottom is kept fairly wide aft so that she can take a reasonable size of outboard (up to 35...

    $101.00
    Choose Options
  • Hinton 15M Plywood Barge Plans

    Hinton 15M Plywood Barge Plans

    This is a simple barge with flat bottom single chine shape and a "swim" shaped stern (under the waterline similar to narrow boats). The bow would be vertically staved plywood in 2 or 3 overlapping layers. Construction details are available for the hull...

    $34.00 - $149.00
    Choose Options
  • 15' Electric Skiff Plans

    15' Electric Skiff Plans

    A lovely little skiff made from four sheets of 1/4’’ plywood using simple stitch and tape techniques. She has a fine entry for moving quickly and easily under electric outboard power (a conventional petrol outboard may also be used) with a stern wide...

    $74.00
    Choose Options