Biminis, Pulpits, Stanchions

Track Fittings

Track Fittings can be used to add slide track to your boat. Track Slides convert standard hinge fittings for track use. End Caps establish the termination point of a Bimini slide assembly. Constructed of UV resistant injection molded nylon.

Jaw Slide & Bracket Fittings

These Jaw Slide & Bracket Fittings are components in a Bimini top fitting system. Bracket Fittings are designed to mount on the side of the gunnel for a Jaw Slide to snap onto. The Jaw Slide then glides along the bracket and is adjusted and secured...

Round Stainless Base Fittings

Part # Description Tube O.D.* Base Fastener SD-280300   30° Round Base 7/8" 2-5/8" #10 FH These Round Rail Base Fittings include set screws where appropriate. Set screws can be purchased separately (299999-1). Requires 1/8" Allen...

Small Top Mount Bimini Deck Hinges

These are the bottom hinges that screw directly into a coaming or deck. In the picture above, you can see that the SD-273230 (left) is angled about 5-7 degrees for cambered or canted decks. The photo above shows the difference between top mount and side...

Bimini Top Inserts

These are used at the ends of the metal hoops which hold up the fabric on a bimini. We have inserts and caps for both 3/4" and 7/8" tubing. Usually Aluminum is used, but we have found that the inserts for 3/4" tubing are almost a perfect fit in 1/2 steel...

Stainless Steel Bimini Top Slide with Bolt

Investment Cast 316 Stainless Steel Top Slide with Bolt for 7/8" tubing. Most biminis have a point where a hoop hinges open or folds up flat. (See image below) These Jaw Slides do just that.

Stainless Side Mount Deck Hinges

Investment Cast 316 Stainless Steel Side Mount Deck Hinge for mounting biminis. Part # Description Base Pin Fastner SD-270250 Side Mount Deck Hinge 7/8" x 2" 1/4" #10FH

Stainless Angle Mount Deck Hinges

Investment Cast 316 Stainless Steel Angle Mount Deck Hinge for mounting biminis. Part # Description Base Pin Fastner SD-270230 Angle Base Deck Hinge 3/4" x 2-1/4" 1/4" #10FH

Standard Side Mount Bimini Deck Hinges

These are the bottom hinges that screw directly into a coaming or deck to mount a bimini. The photo above shows the difference between top mount and side mount and how the end caps or inserts mount on the hinges.

Angled Top Mount Bimini Deck Hinges

These are the bottom hinges that screw directly into a coaming or deck. In the picture above, you can see that the SD-273230 (left) is angled about 5-7 degrees for cambered or canted decks. The photo above shows the difference between top mount and...

Bimini Locking Slide Hinges

Injection molded Nylon These are the bottom hinges that go into an aluminum track and have a built in lock to hold everything in place. They come port and starboard.

Concave Rail Mount Deck Hinges

This hinge is used to mount a bimini to a standard 7/8" rail. It connects to any of our end caps or inserts.

Large Side Mount Bimini Deck Hinges

These are the bottom hinges that screw directly into a coaming or deck to mount a bimini. The photo above shows the difference between top mount and side mount and how the end caps or inserts mount on the hinges.

Snap On/Off Bimini Side Mount

Injection Molded Nylon If you want a bimini that will easily snap out to be completely removed, and is side mounted, you may want to consider this pair. We only have them for 3/4" tubing (also fits 1/2" electrical conduit). The bracket is screwed or...

Bimini Top Caps

Used on the ends of bimini tubing sections These are used at the ends of the metal hoops which hold up the fabric on a bimini. We have inserts and caps for both 3/4" and 7/8" tubing. Usually Aluminum is used, but we have found that the inserts for 3/4"...

Side Mount Bimini Slide Hinges

Injection Molded Nylon

Hinged Bimini Jaw Slide

Most biminis have a point where a hoop hinges open or folds up flat. (See image below) These Jaw Slides do just that. Similar to our Standard Slides, but this slide opens up so it can be installed without having to slide it along a length of tubing...

Square Bimini Jaw Slides

If you want to make a bimini out of square tubing or even square hardwood, you can use these fittings. Use the regular hinges. The square end cap fits 7/8" inside square tubing - 1" x 1" outside tubing dimensions. Most biminis have a point where a hoop...

7/8" Stainless Steel Bimini Top Caps

Investment Cast 316 Stainless Steel top cap for 7/8" tubing.

Standard Top Mount Bimini Deck Hinges

  These are the bottom hinges that screw directly into a coaming or deck. In the picture above, you can see that the SD-273230 (left) is angled about 5-7 degrees for cambered or canted decks. The photo above shows the difference between top mount...

Stainless 90° Mount Deck Hinges

Investment Cast 316 Stainless Steel 90° Mount Deck Hinge for mounting biminis. Part # Description Base Pin Fastner SD-270200 90 degree Deck Hinge 3/4" x 2-1/4" 1/4" #10FH

Bimini Straps

These straps will work in most bimini applications. The 1" wide nylon strap is plenty strong and the chrome plated clip makes it easy to release straps to fold bimini. Straps are used as in the sketch below (straps are marked with "S". You may also want...

Bimini Tube Connectors

A note about tubing/pipe/conduit: Generally speaking, these bimini parts are made to be used with standard aluminum or stainless steel tubing in 3/4" and 7/8" sizes. Other materials such as electrical conduit or pipe can sometimes be used but the fit...

Square Bimini Inserts

If you want to make a bimini out of square tubing, you can use these fittings. Use the regular hinges. The square insert fits 7/8" inside square tubing - 1" x 1" outside tubing dimensions.

180° Universal Deck Hinges

Similar to our Standard Top Mount Deck Hinges, but this deck hinge itself hinges from side to side. It fits all the Sea-Dog Nylon Top Caps and Inserts. The mind boggles at the possibilities for this item.

Curved Windshield Hinges

The hinge above is made to fit a windshield. The opening is 5/8". It connects to any of our top caps or Inserts.

Standard Bimini Jaw Slides

Injection molded Nylon Most biminis have a point where a hoop hinges open or folds up flat. (See image below) These Jaw Slides do just that.

Stainless Rectangular Base Rail Fittings

Investment Cast 316 Stainless Investment Cast 316 Stainless Steel rectangular base rail fittings for mounting lifeline stanchions and pulpits. Set screws included. Part # Description Tube OD Base Fastner SD-281300 30° Rectangular...

Bimini Deck Hinge Slide Lock

SD-273295 - slide lockStainless thumbscrew and nylon nut combination works with aluminum slides.

Stainless Rail Tees

Investment Cast 316 Stainless Steel rail tees for 7/8" tubing. Set screws included.

Standard Bimini Slide Hinges

Injection Molded Nylon