Potter19

Porta-Potti

This portable head is the one factory recommended for the West Wight Potter 19 (and other trailersailers). These self-contained flush toilets feature holding tanks that detach from the fresh water storage tank for easy emptying. Sealed valves keep odors...

Potter 19 Keel Upgrade

This factory upgrade replaces the intrusive steel cable keel-raising system with a rerouted flexible Amsteel (dyneema) line. Kit includes the custom heavy-duty stainless bail.

Potter 19 Backstay Plates

Factory Potter 19 Backstay Plates. These cheeks attach to standard masthead fitting as a critical part of the backstay kit. See the PDF below for original factory installation instructions. We don't yet offer the other components. POTTER 19 BACKSTAY KIT...

Factory Potter Bow and Stern Lights

12V Navigation Lights for use on boats under 65 feet

Factory Potter Masthead Light Bracket

These brackets are used for both the Potter 15 and the Potter 19.

Forestay Tensioning Lever

Mast-raising and rigging goes much easier if you can attach the forestay quickly and easily. These quick-release, adjustable forestay levers from C.Sherman Johnson are the perfect solution for many trailerable sailboats up to around 26-feet. These are...

Potter 19 Bilge Drain

This Garboard Drain & Plug provides drainage for bilge during haul-out. Design includes integral 1-1/8" acetyl drain tube. Pipe plug ensures a watertight seal. Constructed of sturdy UV stabilized injection molded nylon. Installs with three #8 FH...

West Wight Potter Factory Gooseneck

This is the factory West Wight Potter 15 and 19 gooseneck. It does not include any boom pieces, just what it pictured.

Factory West Wight Potter Masthead fittings

Masthead fittings for both Potter 15 and 19

Fixed Mount Combination Masthead / White All-Round Light

Fixed MountBlack Polymer and Chrome Plated Zinc Allow TopBulb: 12 Volt (included)Pole: 3/4" Dia. AnodizedBase Dimensions: 1" x 2-5/8"Mounting Screw Size: #8

Factory Potter Mast Step Pins

These pins are used for the mast steps on the Potter 15 and the Potter 19. Two required for each mast step.

Windex 10.Sport Wind Vane

Windex wind vanes continue to offer exceptional performance at the best value of any wind indicator worldwide. The secret is in the sapphire jewel suspension bearing, large fin-low inertia vane, and easy-to-read, fully adjustable tacking tab system.

Potter 19 Mast Raising Kit

Factory Potter 19 mast raising kit. Includes custom stainless gin pole, assorted blocks, hardware, line, and the sleeve that attaches to the bow pulpit.

Factory Potter Chainplate

These stainless chainplates are used for both the Potter 15 and the Potter 19.

Potter Halyard Kits

Potter 15 and Potter 19 halyard kits made from premium low-stretch Marlow Leisure polyester double braid. Conveniently sent in two colors for easy identification of main or jib and cut to factory-specified lengths (includes enough line to run aft to...

Seadog Stainless Fixed Eye Snap Shackle

Investment Cast Stainless Steel. This is also the factory West Wight Potter halyard shackle. Part Number A B C D SD-143520 2-1/4" 3/8" 9/19" 3/8"

wwp-replacement windows

windows for both Potter 15 and 19

Teak Handrails

We brought these solid teak handrails in to service West Wight Potter owners, as the small one-loop rail is OEM for the Potter 15 and the larger 3-loop is OEM for the Potter 19, but these beautiful, smooth-finished teak handrails would work on any small...

Potter 19 Keel Latch

Factory West Wight Potter 19 Mast Step with pins

This is the factory Potter mast step and will fit most years (some early models are different). The factory riveted the mast foot insode the mast, but 10/32 drill and tap works fine as well.

Seadog Stainless Steel Cleats

Herreshoff style Stainless Steel tie-down cleats. They are resistant to salt and sun, and will outlast your boat. Available in 4, 5, 6, & 8 inch sizes.(Note: the Potter factory specifies the 6" SeaDog Stainless Cleat for its 15 & 19 foot...

Anchor Hanger

These stainless electropolished Anchor Hangers attach securely to any 7/8 to 1” rail or pulpit and will hold most Danforth and Fortress-style anchors up to 35 pounds, flukes down to prevent snagged lines. Allows for quick release. Easy to install...

Potter Cockpit Drain

The cockpit drain looks like the photo - two drain fittings, a couple feet of Bilgeflex hose, and some stainless hose clamps

Low Profile Cowl Vent/Snap-On Deck Plate

These vents bring fresh air into a stuffy cabin. Can be used with a dorade box for an all-weather installation. Made from Dip Molded PVC Dia. Height Mtg. Hole Int. Color 3" 5" 3-3/4" Red

West Wight Potter 19 Factory Tangs

These are the factory West Wight Potter 19 tangs - Long tangs (6") and short tangs (3")

Potter Chainplates

These U-bolts are used for the chainplates on the Potter 15 and for the Baby Stay on the Potter 19

Factory West Wight Potter 15 and 19 Gudgeon

sold individually - mounting fasteners not included

Anchor Roller (bow roller)

Heavy Stainless Steel Factory West Wight Potter Anchor Roller - 10.5" length by 2.25" wide.

Pulpit Anchor

C.S. Johnson Pulpit Anchor. Lots of potential uses for these stainless fittings that slip around and affix on 1" tubing of rails or pulpits, providing a ½" hole to which you can attach a block, lifeline jaw fittings, etc. This piece is a standard part...

1/4" (6mm) Garhauer Cheek Block/Deck Organizer

Garhauer Component Block. Aluminum block will handle up to ¼" line. Good as cheek block or organizer and is commonly used on centerboards. Factory block for the West Wight Potter 19 centerboard. Comes with a pair of 3-inch stainless bolts, stainless...