5/8" Stainless Sail Slides

The strong reliable standard for external sail tracks. Attach with stainless shackles or lace them on. Fits 5/8" external sail track. You may want to use our sailmaker's D-shackles rather than lace or stitch these slides to your sail.

Boom Bails and Hangers

Lots of different sizes RL-333 Racelite Stainless boom bail is 1-1/8" wide but could be bent down to 1" or up to 1-1/2". Strap is 1/2" wide and .062" thick. Holes are 3/16"...

Boom Vang System for Potter 15

Boom vang system for Potter 15. Includes Ronstan block, combo V-jam block, shackle, 2 eye straps, and proper length of polyester double braid.

Factory Potter Chainplate

These stainless chainplates are used for both the Potter 15 and the Potter 19.

Factory West Wight Potter 15 Mast Step with pins

Factory West Wight Potter 19 Mast Step with pins

Forestay Tensioning Lever

Mast-raising and rigging goes much easier if you can attach the forestay quickly and easily. These quick-release, adjustable forestay levers from C.Sherman Johnson are the perfect solution for many trailerable sailboats up to around 26-feet. These are...

Heavy Duty, Stainless Thimbles

Stamped 304 Stainless Heavy duty stamped 304 stainless steel thimbles. The smaller sizes are used to relieve wire rope where it goes around clevises, tangs, chainplates, etc. The larger sizes are typically used with rope such as on anchor lines where...

Potter 15 End Boom Sheeting System

This simple but effective system allows the Potter 15 to be sheeted entirely from the end of the boom, keeping the cockpit clear and the sheet right at hand. Package includes performance Ronstan blocks (one for boom and one for the traveler), and a...

Potter 15 Stem Fitting

West Wight Potter-15 Factory Stem Fitting

Pulpit Anchor

C.S. Johnson Pulpit Anchor. Lots of potential uses for these stainless fittings that slip around and affix on 1" tubing of rails or pulpits, providing a ½" hole to which you can attach a block, lifeline jaw fittings, etc. This piece is a standard part...

Racelite 1/2" Stainless Tangs

Stainless Steel These tangs are made from 0.062" stock and have 3/16" dia holes in the ends. The hole centers are 1/2" from the ends. Nominal lengths are not from hole centers but total overall length.

Racelite 3/4" Stainless Tangs

These tangs are made from 0.062" stock and have 3/16" dia holes in the ends. The hole centers are 3/8" from the ends. Nominal lengths are not from hole centers but total overall length.

Racelite Adjustable Track Eye Slide

For travelers, jibs, sliding stays, etc. 1/4" diameter ring. 5/8" x 3/4" opening. Slide length 3" with thumbscrew for easy adjustment. Stainless steel construction. Fits 5/8" sailtrack.

Racelite Chain Plate Covers

Stainless SteelPart #OverallSlotThicknessMtg HoleRL-344-B2" x 1"1.04" x 0.135"0.060"0.165"RL-4453" x 1.25"2.070" x 0.250"0.090"0.165"RL-4203.5" x 0.878"2.070" x 0.250"0.060"0.200"

Racelite Deck Mounted Chain Plate

Deck mounted shroud chain plate has 1/4" mounting holes on 1-1/2" centers with one 1/4" clevis pin hole. Constructed of 3/32" thick stainless steel bent to a 65 degree angle.

Racelite Deck Plate

This stainless steel deck plate can be used with our RL-349 shroud adjuster or RL-305-A or RL-205 blocks. It comes complete with clevis pin and ring. wt 1/2 oz.

Racelite Deck-Plate

This stainless steel deck plate can be used with our RL-305-B blocks. Takes #8 RH screws. Base 2-1/2" long. Stainless steel. You may need a 5/8" x 3/16" Clevis Pin

Racelite Halyard Shackles

Stainless Steel Light, fast, positive. No cotter pins, New spring tension captive pin maintains steady pressure on sides of shackle undersailing conditions, and allows easier opening for quick release. Stainless steel spring.

Racelite Small Swivel

Stainless steel swivel. Strap is 0.06" by 3/8". 3/8"+ between tangs. 1-5/8" long over all.Takes 3/16" x 1/2" pin.

Racelite Stainless Chain Plates

Stainless Steel Chainplates transfer the stress from standing rigging down into the hull. They may also have other uses for all kinds of applications. Use your imagination. Premium stainless steel made in the USA by Racelite. Cat No...

Racelite Stainless Deck Straps

Stamped Stainless SteelPart No.OpeningWidthLengthFastenersRL-314-A3/8" x 3/8"3/8"3"#8RL-314-B7/16" x 7/16"1/2"3-1/2"#8RL-314-C5/8" x 5/8"1/2"3-7/8"#8

Racelite Stainless Eyes

Stamped Stainless Steel Stamped stainless eyes. Both eyes made from 0.075" strap. Part Length Width Eye Width Hole dia. RL-311 2-1/4" 1/2" 3/4" 3/16" RL-313 1-1/2" 3/8" 3/8" 3/16"

Racelite Stainless Jib Strap

Use with RL-301-A or RL-301-B or RL-305-A or RL-305-B blocks. Takes #10 screws. Weight 1/3 oz.

Racelite Stainless Mast Hounds

RL-425-H - RL-325-H Hounds are what you bolt to a mast to attach a wire stay to. These Race-Lite hounds are the ones made for various boat manufacturers. They are strong and solid. Part No. Mast Size Strap Hole...

Racelite Stainless Shroud Adjusters

Stainless steel - two sizes For coarse adjustment of wire shrouds or stays. Each complete with two 1/4" dia pins and retainer rings. Dimensions: Part Length Width Hole dia. Strap thickness RL-245S 5-1/2" 5/8" 0.264" 0...

Racelite Stainless Spin Strap

The RL-318 Spin Strap from Racelite is used to connect a block to a spar or just about anywhere else. Use with block RL-305-A or RL-205. Takes #10 screws. Weighs 1/3 oz. Here it is used to attach an RL-205 to the top of the mast on our Ladybug sailboat.

Racelite Vang Plates

Stainless SteelThe stainless plates are 1-1/2" x 3" x 0.062" with 3/16" mounting holes. The curved ones are intended for a boom that is 2-3 inches in diameter.The stainless cables are 1/8" diameter x 6" long. The diameter of the button is 5/16"

Ronstan 1/4" Tang

6.4mm (1/4") dia. clevis pin, 51mm (2") long, 1 x 6.4mm (1/4") fixing holeUsed for terminating wire riggingGrade 316 stainless steel0.7 oz. - 20 g

Ronstan 3/16" Tang

5mm (3/16") dia. clevis pin, 76mm (3") long, 2 x 5mm (3/16") fixing holesUsed for terminating wire riggingGrade 316 stainless steel0.5 oz. - 15 g

Ronstan 5/16" Tang

8mm (5/16") dia. clevis pin, 64mm (2 1/2") long, 1 x 9.5mm (3/8") fixing holeUsed for terminating wire riggingGrade 316 stainless steel1.4 oz. - 40 g

Ronstan Brace Hook

Brace hooks are used instead of barber haulers, to hook in the windward spinnaker sheet after gybing.Stainless steel hookNeoprene pad

Ronstan Closed Thimbles

Make eyes in rope or wire ropeRonstan ThimblesCable Ø1/8"1/4 in.A11/32"13/16 in.B3/16"11/32 in.C5/8"1 5/16 in.Weight0.1 oz.0.7 oz.

Ronstan Eye/Eye Ball Bearing Barrel Swivel

Ball bearing swivels like this one have lower friction and higher working loads than non ball bearing versions. Used in conjunction with blocks and rigging systems to provide articulation and rotation. Not suitable for high speed rotating...

Ronstan Mast Hound

Suits mast dia.s between 76mm-115mm (3"-4 1/2") 316 Stainless Used for terminating wire rigging Wt. 3.9oz - 110g

Ronstan S-Hooks

316 Stainless Reference RF48A RF49 A 13/32 in. 13/32 in. B 13/32 in. 7/16 in. C 2-17/32 in. 2-15/16 in...

Ronstan Swivel Cleat Base

Alloy cleating arms Grade 316 stainless steel fittings Swivel cleat bases permit easy cleating and releasing from any angle.Dead eyes contain stainless steel liners for low friction and long life. Cleating plates are heavy guage alloy for stiffness and...

Rubbaweld Rigging Tape

Clevis pins and rings can get hooked on line or otherwise pulled out and consequences can be disastrous. On stayed rigging we suggest wrapping your turnbuckles and other pinned fittings to make sure they don't get snagged or wiggle lose—especially if...

Seadog Closed, Stainless Thimbles

Cast 304 Stainless Heavy duty stamped 304 stainless steel thimbles. These can be used for wire rope and are especially recommended for use with 12 strand Spectra line.For more sizes of these thimbles from Ronstan, click HERE Part...

Seadog Forged Brass Pad Eyes

These Pad Eyes are great for block attachment, controlling lead lines, or creating tie down points. Constructed forged brass wire. Installs with two FH fasteners (not included). Part # A B C Fastner SD-081270 5/16" 3/8" 1-3/8" #8...

Seadog Jaw & Jaw Turnbuckles

Machined 316 Stainless Each Sea-Dog Stainless Turnbuckle is made from AISI 316 stainless steel and features an electropolished bright finish at no additional cost. All thread sizes and wire rope sizes now conform to U.S. standards and are interchangeable...

Seadog Sailmaker's D-Shackles

Stamped 304 Stainless - Made in Denmark These shackles have many potential uses but their primary function is for use attaching sail slugs and slides to grommets. Part No. A B C Breaking Strength SD-140154 3/16" 1/2" 1-1/16" 2,640 lbs...

Seadog Shroud Adjuster

Stainless Steel, 4-1/2 inches long, made in Denmark. This is a special purchase available only in limited numbers.

Seadog Stainless D-Shackles

Note: size = pin diameter Above SD-147110 - SD-147108 - SD-147106 - SD-147104 - SD-147103 Forged 316 Stainless Part No. A B C BreakingStrength SD-147103 5/32" 3/8" 11/16" 1,540 lb. SD-147104 3/16" 7/16" 11/16" 2,200...

Seadog Stainless Fixed Eye Snap Shackle

Investment Cast Stainless Steel. This is also the factory West Wight Potter halyard shackle. Part Number A B C D SD-143520 2-1/4" 3/8" 9/19" 3/8"

Seadog Stainless Long D-Shackles

Note: size = pin diameter Forged 316 Stainless Part No. A B C BreakingStrength SD-147173 5/32" 5/16" 1-5/16" 1,540 lb. SD-147174 3/16" 7/16" 1-9/16" 2,200 lb. SD-147176 1/4" 1/2" 1-7/8" 3,300 lb.  

Seadog Stainless Swivel Eye Boat Snap

Investment Cast 316 Stainless Steel. Part Number A B C SD-146131 3-5/16" 7/16" 3/4"

Seadog Stainless Trigger Snap

Investment Cast 316 Stainless Steel.

Seadog Stainless Twisted Shackles

Note: size = pin diameter Forged 316 Stainless Part No. A B C Breaking Strength SD-147403 5/32" 5/16" 1-1/4" 1540 lbs SD-147404 3/16" 3/8" 1" 2,200 lbs SD-147406 1/4" 1/2" 1-1/4" 3,300...

Small 7 Hole Quick-Release Shroud Levers

Adjust and tension dinghy rigging with the ease of a lever. C. Sherman Johnson shroud adjusters were designed for one design dinghies to make quick rig adjustments or to de-tension the rig for storage or to unstep the mast. 7 positions allow for micro...