RaceLite

Phenolic Through-Deck Fairleads

Any line that goes through a deck needs something like this to protect both the deck and the line. Bakelite (phenolic). All pieces have approx 1/8" flange overhang and 5/8" overall height. Part # Thru Hole(min) Hole Size(for...

Rudder Hardware for Scamp

This set is recommended by John Welsford for Scamp. The tangs are 2-1/8 inches wide and the pintles have a sturdy 3/8" pin.This set consists of two gudgeons and two pintles. There is no hold down included. All parts are stainless steel. (note: pintle...

Racelite Curved Fixed Goosenecks

Racelite Fixed Goosenecks

RL-328 - Fixed Gooseneck - Screws or rivets to standard boom and mast. Base is 1.5" x 3".Shown here with tangs

Racelite Stainless Shroud Adjusters

Stainless steel - two sizes For coarse adjustment of wire shrouds or stays. Each complete with two 1/4" dia pins and retainer rings. Dimensions: Part Length Width Hole dia. Strap thickness RL-245S 5-1/2" 5/8" 0.264" 0...

Racelite 1/2" Pin Heavy Duty Pintles

1/2" pins - 1" & 2" rudders These pintles come in two widths and with either short pin or long pin. There is no gudgeon included. All parts are stainless steel - Fits 1" or 2" thick rudder. (note: pintle tangs can be easily adjusted for rudders as...

Racelite Heavy Duty Rudder Gudgeons

See our pintle & gudgeon compatibility chart Our RL-690 rudder gudgeons are similar to our RL-490 pintles but with no pin. They can be used with the RL-690 transom pintle or with the RL-490 gudgeon if a bolt or rod is run through...

Racelite Stainless Jam Cleat

Designed for halyards, clew outhauls, topping lift pennants, and other general purpose jobs. Narrow 5/8" base. 3-1/4" long. Takes #10 screws.

Racelite Deck Plate

This stainless steel deck plate can be used with our RL-349 shroud adjuster or RL-305-A or RL-205 blocks. It comes complete with clevis pin and ring. wt 1/2 oz.

Racelite Stainless Mast Hounds

RL-425-H - RL-325-H Hounds are what you bolt to a mast to attach a wire stay to. These Race-Lite hounds are the ones made for various boat manufacturers. They are strong and solid. Part No. Mast Size Strap Hole...

Racelite Moveable Goosenecks for 7/8" Sailtrack

RL-427 - slides on 7/8" sailtrack and has a thumbscrew to stop travel.Shown with boom furler option

Weekender Rudder Hardware Set (includes pins and rings)

This is a very robust set of stainless steel rudder hardware. The vertical gudgeon that bolts against the transom is a full 1/8th (0.125) of an inch thick and 1.25" wide. The rudder gudgeons are made from 1" wide strap and are 3/32 (0.090)" thick. The...

Weekender Rudder Gudgeon

These gudgeons were developed for the Weekender Set, but will work with many of our 3/8" pintles. (see chart to figure out which will work) They can also be used on a skeg where a regular gudgeon is used as the upper pivot point. Weekender Rudder...

Racelite Reefing Hook

Reefing Hook - Mount this hook under the Tack Shackle for quick reefing - hook the reef tack under this hook. The base is 1/8" thick and 1.5" x 0.75". The two hooks are made from 1/4" dia. round stock. The mounting hole is 1/4" dia. There is a little...

Racelite Small Stem Fitting

Built with a stem for extra strength. Base 3" long by 1.5" wide tapering to 5/8". Stem is 4" long, 5/8" wide & 0.085" thick w/ 3 1/4" holes. Takes up to 6 #10 screws. Fin has two 1/4" holes and one 3/8" hole. All stainless steel construction.

Racelite Adjustable Track Eye Slide

For travelers, jibs, sliding stays, etc. 1/4" diameter ring. 5/8" x 3/4" opening. Slide length 3" with thumbscrew for easy adjustment. Stainless steel construction. Fits 5/8" sailtrack.

Daggerboard Spring Retainer

Made of spring stainless steel, these retainers are used on Sunfish and many other production sailboats to keep the daggerboard down yet allow it to be easily withdrawn. Length Width Thick 6" 3/4" 0.020"

Canoe/Kayak Rudder Gudgeons

For sharply pointed sterns After a lot of consulting with the folks at Race-Lite and with substantial help from Matt at JEM watercraft, we have finally come up with a good solution to the problem of attaching rudders to canoes and kayaks. Use two of...

Racelite Stainless Utility Hook

Stainless hook holds pole diameters to 1-1/2". Takes #8 oval head screws.

Racelite Heavy Duty Transom Pintles

Our RL-690 transom pintles are the same as used on most Lightning class sailboats. They are typically mounted on a flat transom and paired with a rudder gudgeon. More details under "Particulars" tab. To find out which gudgeons work with these pintles,...

Racelite Light Duty Gudgeons

See our pintle & gudgeon compatibility chart Light duty stainless transom mount gudgeon from Racelite. See Particulars for dimensions. RL-358Light duty stainless steel gudgeon 5/8" x 4" x 1/16"pin - 5/16"takes #10 fastener  

Racelite Stainless Steel Hook

We got a special deal from Race-Lite folks on these handy little hooks. They have quite a few and gave us a big discount on them. They are one inch wide, about 1-3/4 inches long and made of 0.060" material. The holes accept #10 round head fasteners. Buy...

Racelite Small Swivel

Stainless steel swivel. Strap is 0.06" by 3/8". 3/8"+ between tangs. 1-5/8" long over all.Takes 3/16" x 1/2" pin.

Racelite Fixed-Goosenecks

RL-250 - Fixed Gooseneck - Screws or rivets to standard boom - mounting strap is 3/4" wide and set for 2-1/2" mast but could be adjusted 1/2" either way.Shown with tangs

Rudder Hold-downs

RL-336 - Spring TypeStainless Steel spring rudder hold-down - 4" long x 3/4" wide - may be used with any of our pintles and gudgeons. RL-337 - Swivel TypeStainless Steel swivel hold-down - 1" long x 5/8" wide - may be used with any of our pintles and...

Racelite Stainless Chain Plates

Stainless Steel Chainplates transfer the stress from standing rigging down into the hull. They may also have other uses for all kinds of applications. Use your imagination. Premium stainless steel made in the USA by Racelite. Cat No...

Racelite Fairleads

Stainless wrapped fairleads from RaceLite. The smaller one has a 5/16" opening and is suitable for 1/4" lines and smaller. The larger one has an opening of 1/2" and should not be used with line over 3/8".

Set of Light Duty Pintles and Gudgeons

See our pintle & gudgeon compatibility chart This set consists of two gudgeons, one short pin pintle, and one long pin pintle. There is no hold down included. All parts are stainless steel - Fits 3/4" or 1-3/16" thick rudder. (note: pintle tangs can...

Racelite Stainless Jib Strap

Use with RL-301-A or RL-301-B or RL-305-A or RL-305-B blocks. Takes #10 screws. Weight 1/3 oz.

Racelite Bow Fitting

All Stainless heliarc welded construction for extra strength. 3-1/4" long by 1-1/2" wide, tapering to 5/8" at ends. Holes take # 10 flat head screws or bolts. Fin is 2-1/2" long & 1/8" thick with (2) 1/4" holes and (1) 3/8" hole. Complete with matching...

Set of Medium Duty Pintles and Gudgeons

This set consists of two gudgeons, one short pin pintle, and one long pin pintle. There is no hold down included. All parts are stainless steel - Fits 3/4" or 1-3/8" thick rudder. (note: pintle tangs can be easily adjusted for rudders as much as 1/4"...

Racelite 3/4" Stainless Tangs

These tangs are made from 0.062" stock and have 3/16" dia holes in the ends. The hole centers are 3/8" from the ends. Nominal lengths are not from hole centers but total overall length.

Racelite One Piece Gudgeons

A one piece gudgeon ideal for small boats such as PDRacers. Pintle holes are 5/16" but could be drilled to 3/8".Feedback:I recently installed a Racelite 358BR gudgeon as a retrofit on my son's PDRacer (Hull #491). The original rudder hardware consisted...

Racelite Extra Heavy Duty Gudgeons

Extra Heavy duty stainless transom mount gudgeon from Racelite. See Particulars for dimensions. RL-490Extra heavy duty stainless steel gudgeon thickness - .090" plus reinforcing strap3/4" wide x 5-1/4" long x 1" highpin - 3/8"takes...

Racelite Medium Duty Eye Strap

Made of 3/32" Stainless Steel with mounting holes for #10 fasteners on 1-1/2" centers, 9/16" diameter eye. RL-413A1/2in.B5/8 in.C1-1/2 in.Weight.01 lb.

Racelite Tiller Extension Swivel

Often you want a push-pull tiller extension so that you can steer the boat from up on the rail or even from the bench seat if the boat is particularly beamy. This simple swivel from Race-Lite will fill the bill. Two round head #8 or #10 screws mount it...

Racelite RL-260-S Camcleat

These economical yet durable camcleats from Race-Lite are just the thing for quick set and release of sheets and other lines on your sailboat. They are also handy for other jobs where precise adjustment of rope or line is needed. See also RL-261, and...

Racelite Boom Crutch Holder

For fastening to aft cockpit bulkhead. Opening 2-3/4" x 3/4". Takes # 8RH screws.

Racelite RL-261 Camcleat

Similar to the RL-260 camcleat but with a glass-filled flange base for surface mounting. Use four countersunk #8 wood or machine screws. Available with or without stainless steel fairlead/strap. Bolts are on 1-1/2" centers - works best with 7/16" line or...

Racelite Heavy Duty Pintles

3/8" pins - 1" - 1-3/8" rudders These pintles come in two widths and with either short pin or long pin. There is no gudgeon included. All parts are stainless steel - Fits 1" or 1-3/8" thick rudder. (note: pintle tangs can be easily adjusted for rudders...

Racelite Moveable Goosenecks for Bolt Rope Slot

RL-252-A - goes in 1/2" boltrope grove in mast and screws to standard boomShown with tangs

Racelite Shroud Adjuster

This is the RL 349 adjuster for shrouds.

Racelite 1/2" Heavy Duty Gudgeons

Takes 1/2" pintles There are two different gudgeons in this style - one two hole and one four hole - both take 1/2" pintles. Each gudgeon is actually composed of two parts as shown below. All parts are stainless steel.Typically the four hole gudgeon is...

Racelite Nylon Through-Deck Fairleads

Two sizes Use through deck fairleaders for easy and frictionless halyard entry. Large size (RL 42) fits 1" hole, is 5/8" long, and for 3/8" rope. Small size (RL 49) fits 5/8" hole, is 1/2" long, and for 5/16" rope. Part # Thru Hole(min) Hole...

Racelite Light Duty Pintles

5/16" pins - 3/4" - 1-3/16" rudders These pintles come in two widths and with either short pin or long pin. There is no gudgeon included. All parts are stainless steel - Fits 3/4" or 1-3/16" thick rudder. (note: pintle tangs can be easily adjusted for...

Sets of Extra Heavy Duty Transom Pintles and Rudder Gudgeons

See our pintle & gudgeon compatibility chart This set consists of two gudgeons and two pintles. There is no hold down included. All parts are stainless steel - Fits 1-1/2" through 3" thick rudders. (note: pintle tangs cannot be adjusted for rudder...

Racelite RL-260 Camcleat

These economical yet durable camcleats from Race-Lite are just the thing for quick set and release of sheets and other lines on your sailboat. They are also handy for other jobs where precise adjustment of rope or line is needed. See also RL-261, and...

Racelite Deck Mounted Chain Plate

Deck mounted shroud chain plate has 1/4" mounting holes on 1-1/2" centers with one 1/4" clevis pin hole. Constructed of 3/32" thick stainless steel bent to a 65 degree angle.

Racelite Stainless Deck Straps

Stamped Stainless SteelPart No.OpeningWidthLengthFastenersRL-314-A3/8" x 3/8"3/8"3"#8RL-314-B7/16" x 7/16"1/2"3-1/2"#8RL-314-C5/8" x 5/8"1/2"3-7/8"#8

Racelite Medium Duty Pintles

3/8" pins - 3/4" - 1-1-4" rudders These pintles come in two widths and with either short pin or long pin. There is no gudgeon included. All parts are stainless steel - Fits 3/4" or 1-1/4" thick rudder. (note: pintle tangs can be easily adjusted for...