Skylark 6' Plans

Although only 6' long we have given her good internal volume with a beam of 3'8". This gives plenty of buoyancy in the ends of the boat so that she does not exhibit the usual tippiness of craft of this size. Her overall weight will be less than 50 lbs...

24' Tasman Junk Rigged Yacht Plans

The Tasman is a multi-chine plywood yacht designed for long distance sailing for 2 crew, which uses an egg-box frame system of plywood fore and aft girders slotted together with plywood bulkheads - once stringers have been fitted, the ply hull panels are...

15' Electric Skiff Plans

A lovely little skiff made from four sheets of 1/4’’ plywood using simple stitch and tape techniques. She has a fine entry for moving quickly and easily under electric outboard power (a conventional petrol outboard may also be used) with a stern wide...

36' Hawfinch Wood Narrowboat Plans

We have often been asked for a wood version of a steel narrowboat and here it is. Narrowboats were of course made from timber in the first part of the last century although then, they used heavy boards of Elm and Oak. This version uses several layers...

Edwardian 26 Plans

Having put the lines of an original 25’ LIFU launch into our computer system we have used this shape in the development of this 26’ Edwardian Launch. The LIFU launches were very successful and were known for their good sea keeping qualities...

Power 3 Plans

Soon after our Power 2.2 left the drawing board, we were asked to extend it and produce a design which, in a compact form, could accommodate a large aft cabin with a central wheelhouse and forward dinette. So the beam has been increased to...

Cegall 11' Plans

The Cegall has been designed for Chippendale Craft and is very much based upon the 14' Kingfisher design. The method of construction is just the same with a pre-shaped ply centre girder forming the centreboard case and stem - this is epoxied to the...

14' Fisher Prospector Plans

A 14' version of our most popular canoe design - the 15' 8" Fisher Prospector. Over the years, the 15'8" Prospector has been cut down by those wanting a shorter version simply by cutting a piece out of the middle - this works but is not ideal and so I...

26' Golden Virginia Launch

Pete Greenfield, Editor of the Watercraft Magazine asked me to design this launch and is going to partly finance it by giving up smoking, hence the name Golden Virginia ! She is strip planked and is fitted out with settee berths and simple basic wc and...

Dart 22 Plans

The DART 22 uses a similar section to that of the Dart 16. This consists of a tortured ply ‘U’ shape which changes fore and aft into a full ‘V’ giving adequate buoyancy and a good entry at the fore foot. Above the shaped bottom there is a soft...

Shetland 14 Workboat Plans

This sturdy craft has been designed for a client in Scotland who wanted a rugged general purpose boat for fishing and diving in rough water. She may only be 14’ long, but she is for all that, a large boat and she incorporates both integral buoyancy...

36' Motor Yacht Plans

The drawings for this 36' motor yacht consist of lines, offsets, layout and profile details. Construction drawings and details can be furnished to the client to suit whatever method of build he requires. For the discerning motor yachtsman wanting a...

Westray 9 Plans

Several years ago I was asked by PJS Boats to draw up a modified Highlander 16 dayboat with a real seagoing jaunty sheer and plenty of stability to take a powerful rig. The Westray 16 was born and later they asked me to design a smaller dinghy in...

24' Strip Planked Motor Yacht Plans

This was a commission just for the computer generated and faired mould shapes and building jig details for a 24' x 8'6" motor yacht of traditional appearance. The concept is to have a forward cabin with 2 berths plus wc and galley and either a short...

16' Petite Brise Plans

The 12’4’’ Petite Brise has proven to be very popular and we have had several requests for a longer version, so we have gone for a hull length of 16’ and increased the beam to 5’9’’. Like her smaller sister, we...

Dart 16 Plans

The Dart 16 double kayak has a soft ‘U’ shaped bottom running into flared ‘V’ sections fore and aft with a chine, giving a very stable shape. She has a large 7’ long cockpit and with her 32’’ (0.81m) beam she is...

Heron 15 Pocket Cruiser Plans

The additional 1'4" hull length over the original 14' version gives a lot of useful additional space - enough for 2 comfortable berths, a small galley area and curtained side space for a Porta Potti type wc. Unlike the 14 foot which has fixed bilge...

14' Thames Skiff Plans

This is a 14’ (4.27m) x 4’2” (1.27m) stitch and tape/clinker/ply Thames Skiff – similar to our Thames 12 skiff - for Mr. B. Lammerton - she retains the same “wineglass” type transom and construction is for stitch &...

15'1" Port Pegasus Plans

The Port Pegasus is a clinker boat which may be used as a pure rowing boat or fitted with a small diesel (ie Farymann 7.5) as a small motor launch with classic appearance.   As a general purpose launch, she could be fitted out in a variety of...

16' Mystery Plans

16’x 6’4’’x 8’’ (3’6’’ with board down). Approx. 450 lbs. lightweight with 120 lbs. of ballast. An ultra simple cruiser of double chine shape using pre-shaped ply panels for the hull. Can sleep two in the cabin and two in the cockpit...

St. Bronagh 18' Strip Planked Skiff Plans

Plans are now available here for the double ended St.Bronagh skiff designed for Tyrone Boats for coastal rowing - she has a low wetted surface area hull capable of excellent performance in offshore conditions with two crew and a cox. The plans are for...

Power 1.3 Plans

The Power 1.3 is a development of the original Power 1 design. In this case, we were asked to produce a simply built hull with more capacity and suitable for offshore and estuary conditions. We have retained the flat bottom section which eases and...

21' Ijssel Launch Plans

This launch has been designed for diesel propulsion (10-15 hp) but she can also take steam or electric propulsion. The layout drawn for her is a simple open thro' plan with no obstructing bulkheads but she could be fitted out in a variety of ways - a...

18'4" Tosher

Apparently, "Toshing" was the taking of copper from laid-up warships. We have used the Mevagissey Tosher as the model for this boat. They were renowned for their speed and sea keeping qualities and apart from removing copper they were also used for...

18' Bungay Broads Dayboat

This design is based upon the traditional daysailers and small yachts that can be hired on the Norfolk Broads. Construction is Cedar strip planking over computer faired moulds/jig. The mast is stepped in a tabernacle for easy raising/lowering and she can...

27' Northumbrian Coble

Most East Coast Cobles were of clinker (lapstrake) construction but a few were carvel and the 27’ Northumbrian Coble emulates one of these by using modern strip planked construction. I have not attempted to ‘modernize’ the concept too much and so...

19'6" Lark Dory

19’6’’x 5’8’’x 11’’ (min.). May be built in two halves and bolted together as a fishing/motor dory or as a sailing dory with or without the cubby/cabin. Pre-shaped side hull panels are fastened to the...

JC10 Plans

The JayCee was conceived with Tyrone Boats as a trainer for the International Canoe. The idea was to produce a craft which was based upon low cost, easy building techniques and which would be an introduction into the world of IC sailing. With all this...

Loddon 20' Strip Planked or FRP Skiff Plans

The Loddon 20 is round bilged and can be made using foam sandwich (FRP) and strip plank Cedar construction methods. The moulds, transom and inner stem shape. She is designed for 2 or 3 rowing plus a cox or 2 rowing plus cox and passenger. The hull shape...

14' Exe Dory Plans

Looking for an enjoyable way to exercise, and a pleasurable few weekends working with your hands? If so, then the 14ft. EXE DORY will certainly meet your requirements. Very simple in construction, using the stitch and tape method to produce a strong and...

Skellig 18 Plans

The Skellig 18 is based on our Skellig 26 workboat/fishing boat. She has a double chined V bottom shape with generous beam making her a very stable working platform for all kinds of duties. The hull, with it's high volume and weight carrying capacity...

17' Hazelnut Open Canoe

The requirement was for a canoe with the same stability, capacity and maneuverability as the 17' Prospector but without the high swept back ends and a flatter sheer line. So I took the Prospector model and kept the same mid-section with it's tumblehome...

Highlander 23 Plans

At last, a bigger Highlander dayboat - so really a pocket cruiser or small yacht. She has been drawn up for clinker ply construction over a framework of ply girders and bulkheads but the hull planks shapes are also given for her to be built using the...

Drake 18' Sharpie Plans

A very simple 18’x 5’2’’ ply sharpie drawn with a simple unstayed sprit boom rig and a ply centreboard. Ideal for estuary cruising and an excellent ‘big’ boat for first time construction. In it’s basic form 10 sheets of 3/8’’ ply and 1...

Explorer 16 Plans

The Explorer 16 is a strip planked canoe with fine lines towards the bow and stern running into an easy 'U' shaped mid body. She has tumblehome in the topsides which make her easy to paddle and which puts the maximum beam at the waterline giving...

16' Casco Bay Canoe Yawl Plans

The Casco Bay 16 was designed for Maurice Byrne of the Boatyard Upstairs for a Swiss client who wanted a fast, easily handled canoe yawl for use on his home lakes. We have developed an efficient and stable hull form with slight influence from the Casco...

Deben 400 Rowing Skiff Plans

The Deben 400 is a rowing skiff inspired by the Cornish Flashboats—they were 18’ or more in length and used around Fowey for river transport. This version is just under 13’ long and for single recreational rowing. She has a narrow flat bottom...

Docat Suppliment Plans

This is a suppliment - you also need Exe Dory plans to build this boat Based upon two EXE DORY hulls, this nippy little catarmaran makes the ideal beach boat and swimming platform for the family. Existing EXE DORIES can be converted...

Simplicity 8 Plans

This is a very simple but pretty single chine 'V' bottom dinghy designed for use as a tender, fishing boat, or with her simple lug rig, as a sail trainer for your children. Length is 7'9" (2.36m); Beam 4' (1.23m); Weight approx. 55 lbs (25 kg)...

39' Chaffinch Narrow Boat Plans

The Chaffinch is a trad sterned narrow boat - drawings give the computer faired and generated hull panel shapes and full details for steel construction. The steel work drawings give details for the FW tank, rudder, sterngear/engine installation and weed...

Highlander 19'6" Plans

This boat is a stretched version of the Highlander 18 for a client who wanted the biggest boat that he could comfortably trail extensively behind a medium sized family saloon without a lot of effort and which could also offer enclosed accommodation. The...

18'6" Marathon Asymmetric Canoe

The 18’6” Marathon open canoe has been designed for serious long distance paddling. She has 5 planks per side and uses the stitch and tape method of construction for ease, low cost and lightness. Her hull shape is asymmetric giving her a low drag...

20' Fisher Skipjack Plans

The origin of the skipjack is a little obscure - they seem to have been a development of the flat bottomed sharpie with many examples having a much wider beam than the sharpie, a deadrise to the bottom and great flare to the topsides. However,...

23' Martlet Pilot Cutter Plans

The 30' LOD Martlet has been a popular design and represents a lot of seaworthy boat for her length but I have often been asked about a smaller version - a design which embodies the robust pilot cutter looks and sea keeping qualities and the ability to...

Cat 19 Plans

The CAT 19 features 4 berths inside the hulls (and space for others under a tent on the bridge deck), easy trailability (the cross beams are tied to the hulls which also give a degree of flexibility) and very easy construction with the same pre shaped...

Explorer 15 Plans

This design is a slightly smaller sister to our Explorer 16' open strip planked canoe - in this case we have used a similar hull design with a 'U' shaped mid body with plenty of tumblehome in the topsides making her easy to paddle and very stable...

40' Dragon Plans

Well, this is a boat for the purely insane or totally inebriated!, and it is an example of the wide range of boat designs that we are asked to produce from clients all over the world. Basically, she is a slightly thinned and greatly stretched Waterman...

16' Simple Surf Cat Plans

16'€™x 7'€™. Very simple construction based upon 7 sheets of ply and easy "V" section hulls with no centreboards. Costs have been kept right down by using wood beams and a simple ply aerofoil section mast. Definitely a sporty fun boat for the beach and...

15' Medway Doble Plans

We were asked by a Portuguese client to stretch our standard Medway Doble to produce an easily rowed craft which could be carried under the bridge deck of a large cruising catamaran and used both as a tender and as a lifeboat. This version has the same...

Ruby 22' Double Chine Plywood Launch Plans

For those steam enthusiast who want an elegant 22’ steam launch of Edwardian profile but who do not want to spend the time and additional cost of producing a strip planked hull, we have designed Ruby. Our client originally thought of having her...